Start with the project’s voltage definition
When project documents refer to a 35 kV system, first identify exactly what that value describes. It may be the nominal system voltage, a line-to-line value, or shorthand used in a preliminary scope. Those meanings are not interchangeable with the maximum voltage for which equipment is designed. A switchgear specification should state the system basis clearly and identify the required equipment voltage class and applicable maximum operating voltage.
This distinction matters because operating conditions can extend beyond a nominal value, and the equipment must be selected against the actual system and design criteria. Do not assume that equipment labeled “35 kV” has a universal maximum-voltage rating or is suitable for every network described that way. The responsible electrical engineer should reconcile project drawings, utility information, and equipment documentation before finalizing the specification.
Establish the system’s operating envelope
Ask the utility or source-system representative for the expected operating-voltage range and any project-specific voltage conditions that affect equipment selection. Confirm whether the stated system voltage is phase-to-phase, and document the phase arrangement, frequency, conductor configuration, and grounding method. These details help distinguish the actual electrical environment from a broad voltage label and inform the equipment’s insulation and protection requirements.
Review both normal and relevant abnormal system conditions with the project engineer. The appropriate maximum operating voltage and insulation coordination depend on the defined system, switching environment, and applicable design criteria; they should not be inferred from the nominal value alone. Equipment documentation needs to identify the applicable ratings and limitations for the proposed configuration, with any open questions resolved before procurement rather than left to field interpretation.
Match insulation and protection to the application
Insulation requirements are part of a coordinated design, not a standalone choice based on “35 kV.” The engineer should evaluate the system’s voltage range, grounding, exposure to switching or other specified overvoltage conditions, and the protection scheme. Confirm which insulation levels and related equipment characteristics are required for the application, and require the supplier’s documentation to identify the basis for the offered configuration.
Utility protection requirements may shape the interface between incoming circuits, protective devices, metering, and control. Request the applicable utility criteria and approved one-line or interconnection information rather than assuming a standard arrangement. The project team should confirm protective-device functions, instrument-transformer requirements, control-power needs, and coordination responsibilities for the specific design. These are engineering decisions; a voltage designation by itself does not define them.
Check fault duty and system interfaces
Voltage suitability does not establish short-circuit suitability. Provide available fault current at the equipment location, the basis and date of that information, and any required future-system condition identified by the utility or engineer. The engineer must compare that duty with the ratings and documentation of the specific proposed assembly and devices. Do not infer interrupting, withstand, or other fault capabilities from the 35 kV label.
Also clarify how the switchgear connects to the source and downstream equipment. Identify cable termination requirements, bus or conductor interfaces, enclosure location and environmental conditions, access constraints, and the project’s grounding approach. Confirm which party supplies, reviews, and approves drawings, protection settings, utility interfaces, and installation details. These boundaries reduce the chance that a technically suitable voltage class is paired with incompatible connections or incomplete project responsibilities.
Keep class, standard, and scope distinct
“35 kV” should be treated as a project system designation until the engineer confirms the required equipment class and its documented ratings. Medium-voltage equipment requirements depend on the complete specification, including operating voltage, insulation, fault duty, construction, and intended service. Avoid translating a nominal system value directly into a product choice or assuming that similarly labeled assemblies share the same capabilities.
Identify the equipment standard or standards required by the project and utility, then verify applicability to the exact equipment type and configuration. Ask for the documentation needed to establish the proposed assembly’s ratings, construction, and any applicable listing or testing status. Do not presume that a particular standard, listing, or test applies universally. The specification and the supplied equipment documents should agree, and unresolved exceptions should be reviewed by the responsible engineer before release.
Prepare a useful specification package
For a manufacturer quotation, provide the latest one-line diagram, utility or source voltage data, phase and conductor arrangement, grounding method, available fault current, and the applicable project and utility criteria. Include the intended application, installation environment, cable or bus interfaces, protection and metering scope, and drawing or review requirements. Mark assumptions and identify who will approve the final technical submittal.
Ask the project engineer to confirm the maximum operating voltage, insulation requirements, fault-duty basis, and equipment suitability before an order is finalized. Availability and delivery timing depend on the specified configuration and must be confirmed for the actual order. South Carolina Switchgear Builders manufactures new equipment to specification, with US-built equipment, all-American components, short lead times, and nationwide shipping; confirm the requested design and schedule for your project. A complete, reviewed specification gives the manufacturer a sound basis to quote equipment without treating “35 kV” as a complete engineering requirement.