REQUEST A QUOTE

Switchgear specification guide

How to Specify Continuous Current Ratings for Switchgear

A practical guide to matching continuous-current ratings to documented loads, equipment components, and operating conditions.

POWER DISTRIBUTIONBUILT WITH PURPOSE
Rows of switchgear cabinets on an industrial assembly floor
Equipment photograph supplied for illustration.
THE DETAILS MATTERMade for the
work ahead.
MADE IN USAAmerican manufacturing
UL 891Switchboard standard reference

UL 891 is a switchboard standard, not a claim of certification. Confirm applicability and listing for each assembly.

01 / PROJECT INPUTS

The right details make the difference.

Start with the requirements that shape your equipment. Share what you know, and identify what needs discussion.

Discuss your project
PROJECT SPECIFICATIONSREFERENCE / 01
Information to share about your switchgear project
DetailWhat to share
EquipmentType of switchgear or distribution equipment needed
ElectricalRequired voltage, current, and fault-duty criteria
ConfigurationInstallation environment, space, and access requirements
DocumentationDrawings, schedules, applicable standards, and desired listings

Requirements and applicable listings depend on the specific project and equipment.

What a continuous-current rating covers

A continuous-current rating describes the current an assembly or component is intended to carry continuously under its stated design and operating conditions. For a switchgear project, it is not enough to select one number and assume every part of the equipment can carry that current. The specification needs to address the assembly, bus, switching and protective devices, connections, and the conditions used to establish the rating.

Start with the load the equipment will serve, not a preferred catalog value. Normal load current may be based on measured demand, an engineered load schedule, or a documented operating forecast. Identify which loads run together, which are intermittent, and whether future additions are planned. The responsible project engineer should determine how applicable codes and project criteria treat those loads and any required capacity margin.

Evaluate the load and operating profile

Provide the manufacturer with the system voltage class, load schedule, expected demand, and operating profile. Include motor or other significant load characteristics when relevant, along with any known simultaneous operating conditions. If measurements inform the design, describe how and when they were collected and whether they represent typical, peak, or seasonal operation. Measurements help characterize existing demand, but they do not replace engineering review of future or abnormal operating scenarios.

Ask the project engineer to distinguish continuous duty from short-duration or intermittent demand and to document assumptions. A simple total of connected nameplate loads may not represent actual operating current; conversely, a low observed demand may not capture a planned expansion or an uncommon but necessary operating mode. The selected rating should follow the project’s documented load basis rather than an unsupported rule of thumb.

Match bus and device ratings

Review the main bus and each relevant device rating as separate specification items. A bus rating does not, by itself, establish the rating of every breaker, switch, termination, or feeder. The assembly design must coordinate the ratings of its components with the intended current and the stated conditions. Request confirmation that the proposed configuration meets the project requirements as a complete design, rather than relying on a single headline number.

For example, a 480 V-class low-voltage design and a 5 kV- or 15 kV-class medium-voltage design involve different equipment and component configurations. In either case, the engineer should provide load and operating information, while the manufacturer confirms the applicable component and assembly ratings for the proposed design. Do not assume that rating conventions, available device choices, or design limits transfer unchanged between voltage classes.

Account for temperature and installation conditions

Continuous-current capability depends on the conditions stated for the equipment. The project team should document expected ambient temperature, enclosure and room conditions, ventilation, installation arrangement, and any other environmental factors identified in the specification. These details can affect equipment selection and may require a design-specific review. Do not presume that a rating established under one set of conditions automatically applies in a different installation.

Where a project has unusual heat, restricted ventilation, high elevation, close equipment spacing, or other potentially consequential conditions, flag them early for engineering review. The responsible engineer and manufacturer should determine whether the proposed design requires a different configuration or a confirmed adjustment to the applicable rating. Avoid applying an assumed derating factor without a technical basis tied to the actual equipment and its documented conditions.

Balance capacity, fit, and future needs

Choosing a rating that is too close to an uncertain load forecast can constrain later changes, while specifying substantially more capacity than the project needs may affect equipment size, arrangement, and cost. The right tradeoff depends on a documented load outlook, operational priorities, available space, and the project’s plans for expansion. Ask the engineer to state the design basis and explain how foreseeable additions are reflected in the selected equipment.

Do not treat continuous current as a substitute for short-circuit capability or other system requirements. These are distinct specification questions and should be reviewed together so the proposed equipment addresses the complete application. Confirm the required ratings and design criteria with the responsible engineer, then ask the manufacturer to identify how the submitted configuration corresponds to those requirements.

Prepare a useful equipment specification

Before requesting a proposal for new equipment, assemble the one-line diagram, system voltage, load schedule, demand basis, and operating profile. State the required bus and device ratings where established, identify expected environmental and installation conditions, and note expansion assumptions. Include the project location, preferred arrangement, schedule needs, and applicable project documents. If a value remains undecided, label it as an open engineering item instead of presenting an estimate as final.

Request a written response identifying the proposed assembly and component ratings, assumptions, exceptions, and any information still needed to confirm the design. Ask whether listing or other project-specific requirements apply to the exact proposed equipment; applicability must be verified for that design. For eligible low-voltage switchboards, UL 891 may apply, but its applicability and the assembly listing require confirmation. It does not establish a rating for every switchgear configuration.

Coordinate review through procurement

During specification review, keep the engineer, equipment manufacturer, and procurement team aligned on the same load basis and installation conditions. Resolve discrepancies between drawings, schedules, and written requirements before release for manufacturing. Confirm availability and delivery expectations for the specific order; actual timing depends on the equipment and must be verified. South Carolina Switchgear Builders manufactures new equipment to specification, with US-built equipment, all-American components, and nationwide shipping.

After delivery, installation, testing, and maintenance should be performed by qualified personnel following applicable safety procedures and project documentation. Preserve the approved equipment submittals and rating information for commissioning and future engineering changes. A clear continuous-current specification connects the expected load to the actual proposed assembly, its components, and its operating environment—giving the project team a sound basis for selection and coordination.

03 / START A CONVERSATION

Let’s talk about your project.

Tell us what you’re working on and the details you have so far. You can include drawings and other documents in your email.

Prefer to call? (951) 403-5738

Email sales: saleselectricalbuyers@gmail.com

PROJECT INQUIRY01 — 04

* Required fields. This form opens your email application; send the prepared message there, or email us directly. You can also call (951) 403-5738.